![]() ![]()
Some are free/cheap and some are expensive. So instead of having a 1073 on the snare and an SSL on the overheads and a Trident on the kick, you have one emulation for all tracks.Īs others have pointed out, there are other console emulations out there that should do the same thing as long as you apply them across your entire project. The idea is that the tracks should fight each other less and "mesh" more than if you use the typical approach of treating each source with whatever pre/eq/comp combination make each track sound best in isolation. ![]() ![]() I mentioned it here because it seems like a lot of the presumed mojo with MixBus is based on the idea that every channel, bus and output track use the same "console strip" with the same emulation of EQ, compression, gain staging etc. It's commonly available on Reverb around $400. = Please contact PreSonus Technical Support by creating a Support Ticket at My./Support for further assistance.It is a package consisting of console emulation plugins and a hardware controller. #Studiolive mixbus windowsWDM assignments are how Windows interprets channels to and from the StudioLive- globally.īy rearranging WDM 1/2 to a Mix pair, when recording in a DAW (such as StudioOne) Tracks 1 and 2 are no longer receiving audio from Inputs 1/2 of the Console and instead would record/hear Aux1/2 as assigned in our example. Please note, "StudioLive AUX1" corresponds to channel 33 (Channel 17 for SL16.4.2 and Channel 25 for SL24.4.2 AI) of the "Aux Routing" tab in Universal Control. Your StudioLive should now input the Aux or L/R Mix (depending on what is setup) to your software.īe sure to choose the StudioLive/FireStudio as your Audio Device. Drag WDM 1 and WDM 2 from the left side to "StudioLive AUX1" and "AUX2" (shown below)Īfter assigning WDM 1/2 to the Aux output of your choice,.Choose the "Inputs" option in the top-left corner.To reroute WDM Channels for your Firewire StudioLive, #Studiolive mixbus windows 10Reminder: WDM channels are the channels of Windows 10 itself, and can be rearranged/rerouted, but are 1:1 by default. By default, our example channels would be assigned to WDM 33/34. #Studiolive mixbus softwareHowever, keeping in mind that Broadcast and Streaming software only sees WDM 1/2, we would still need to re-route channels 33/34 into Windows's WDM 1/2. This will output our Aux Mix 1/2 from the StudioLive into the computer to be recorded on channels 33/34. We used a StudioLive 32.4.2 AI, and assigned our Aux Mix 1/2 to channels 33/34. The "Aux Routing" tab can be found by logging into the StudioLive AI/RM and then choosing the settings "Gear" icon in the top-right corner. This is done in Universal Control's "Aux Routing" section in the device setting for the StudioLive AI/RM (shown below). To Assign/choose your Main or Aux pair to WDM 1/2 for Streams/Broadcasting:įirst, you will need to assign the Mix you have chosen for your Broadcast feed to a pair of Channels to be sent to the computer. This Stream mix can be separate from the Main L/R output using a pair of Aux mixes OR can be arranged to feed the Main L/R mix verbatim. With Streaming, you will need to rearrange WDM 1 and WDM 2 to be the Output-pair of Channels to which you will be mixing the feed/live-stream. Meaning, usually WDM 1/2 are assigned to Input Channel 1 and 2 by default from the StudioLive AI/RM. Usually Firewire/WDM routing are defaulted to be 1-to-1. More specifically, Streaming software will only accept USB Send 1/2 or WDM 1/2 (Firewire) from the StudioLive or other USB/Firewire Interfaces, mixers, etc. Most Streaming Software will only accept two (2) channels for their Input to the feed or Live-Stream. #Studiolive mixbus updateStudioLive RM (RML) series Firmware Update (via USB thumb drive)įirst, it's important to note a main functional difference between Recording software (DAWs) and Live-Streaming software: ![]() StudioLive AI console Firmware Update (via USB thumb drive) Before proceeding please be sure your firmware is updated on your StudioLive and that you are using the latest Universal Control: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |